[KARAOKE]
[DJ GEAR] [GUITARS]
[LIGHTING] [LIGHT
BULBS] [NEW GEAR] [USED
GEAR] [RENTALS] [BLOWOUTS!]
[ Home ]
[ Feedback ]
[ Contents ]
[ Search ] [Browse
by Brand]
Crown XLS 602 Amplifier
CROWN XLS 602 Amplifier at the lowest prices! Power Alley is an
authorized dealer for the CROWN XLS 602 Amplifier! Free shipping on the CROWN
XLS 602 Amplifier. Call 800-788-9552 for the best deal on
the CROWN XLS 602 Amplifier!
Specifications
The following applies to units in Stereo mode with 8-ohm
loads and rated input sensitivity unless otherwise specified.
Performance
Sensitivity (volts RMS) for full rated power at 4 ohms,
XLS-202: 0.725
XLS-402: 1.025
XLS-602: 1.26.
Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.75 dB.
Phase Response (degrees at 1 watt)
at 10 Hz: –10.
at 20 kHz: +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: > 100 dB.
No weighting, below rated power: > 95 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 1
kHz: < 0.5%.
Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from full rated
output to –40 dB:
< 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
Crosstalk (below rated power)
at 1 kHz: –82 dB.
at 20 kHz: –58 dB.
Voltage Gain (at maximum output): 31 dB.
Power
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in
Stereo, 8 ohms in Bridge-Mono.
AC Line Voltages Available (±10%): 120VAC, 60 Hz and 230VAC, 50 Hz.
Controls
Level: Two front-panel, black rotary level controls, one for each
channel.
Power: Front-panel switch; on when in the UP position.
Circuit Breaker: Provides overload protection.
Indicators
Clip: Two front-panel red LEDs, one for each channel,
illuminate when the channel’s output signal is being overdriven.
Power: Green front-panel LED indicates amplifier has been
turned on and AC power is available.
Fault: Yellow front-panel LED illuminates when amplifier is in
protect mode. Also illuminates briefly during normal power-up when
amplifier is first switched on.
Input/Output
Input Connectors: One per channel; back-panel three-pin female
XLR input connectors.
Input Impedance: (nominally balanced, nominally unbalanced): 20
k ohms, 10 k ohms.
Output Connectors: Two 4-pole Speakon® connectors
(one per channel) and two pairs of 5-way binding posts; accepts
banana plugs, spade lugs or bare wire. (European models do not accept
banana plugs.)
DC Output Offset (shorted input): ±10 millivolts.
Output Signal: Stereo, unbalanced, two-channel.
Protection
XLS Series amplifiers provide extensive protection, including output
current limiting, DC protection, circuit breaker, and special thermal
protection for the unit’s transformers.
Construction
Ventilation: Flow-through ventilation from front to back.
Cooling: Internal heat sinks with forced-air cooling for rapid,
uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27
m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA
RS-310-B), 3.5-inch (8.9-cm) height and 14-inch (35.6-cm) depth behind
the mounting surface.
Weight
Net Weight,
XLS-202: 21.0 lbs. (9.5 kg);
XLS-402: 25.3 lbs. (11.5 kg);
XLS-602: 27.2 lbs. (12.3 kg).
Shipping Weight,
XLS-202: 26.0 lbs. (11.8 kg);
XLS-402: 30.3 lbs. (13.8 kg);
XLS-602: 32.2 lbs. (14.6 kg). |
|